View PCA6408AHK_6038173.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

1. general description the pca6408a is an 8-bit general purpose i/o expander that provides remote i/o expansion for most microcon troller families via the i 2 c-bus interface. nxp i/o expanders provide a simple solution when additional i/os are needed while keeping interconnections to a minimum, for example, in battery-powered mobile applications for interfacing to sensors, push buttons, keypad, etc. in addition to providing a flexible set of gpios, it simplifies interco nnection of a processor running at one voltage level to i/o devices operating at a different (usually higher) voltage level. the pca6408a has built-in level shifting feature that make s these devices extremely flexible in mixed signal environments where communication between incompatible i/o voltages is required. its wide v dd range of 1.65 v to 5.5 v on the dual power rail allows seamless communications with next-generation low voltage microprocessors and microcontrollers on the interface side (sda/scl) and peripherals at a higher voltage on the port side. there are two supply voltages for pca6408a: v dd(i2c-bus) and v dd(p) . v dd(i2c-bus) provides the supply voltage for the interfac e at the master side (for example, a microcontroller) and the v dd(p) provides the supply for core circuits and port p. the bidirectional voltage level translation in the pca6408a is provided through v dd(i2c-bus) . v dd(i2c-bus) should be connected to the v dd of the external scl/sda lines. this indicates the v dd level of the i 2 c-bus to the pca6408a. the voltage level on port p of the pca6408a is determined by the v dd(p) . the pca6408a consists of one 8-bit configur ation (input or output selection), input, output, and polarity inversion (active high) re gister. at power-on, the i/os are configured as inputs. however, the system master can enable the i/os as either inputs or outputs by writing to the i/o configuration bits. the data for each input or ou tput is kept in the corresponding input or output register. the polarity of the input port register can be inverted with the polarity invers ion register, saving interrupts. the system master can reset the pca6408a in the event of a time-out or other improper operation by asserti ng a low in the reset input. the power-on reset puts the registers in their default state and initializes the i 2 c-bus/smbus state machine. the reset pin causes the same reset/in itialization to occur witho ut de-powering the part. the pca6408a open-drain interrupt (int ) output is activated when any input state differs from its corresponding input port register state and is used to indicate to the system master that an input state has changed. int can be connected to the interrupt input of a microcontroller. by sending an interrupt signal on this line, the remote i/o can inform the microcontroller if there is incoming data on its ports without having to communicate via the i 2 c-bus. thus, the pca6408a can remain a simple slave device. pca6408a low-voltage, 8-bit i 2 c-bus and smbus i/o expander with interrupt output, rese t, and configuration registers rev. 1 ? 27 september 2012 product data sheet
pca6408a all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2012. all rights reserved. product data sheet rev. 1 ? 27 september 2012 2 of 40 nxp semiconductors pca6408a low-voltage, 8-bit i 2 c-bus and smbus i/o expander the device port p outputs have 25 ma sink ca pabilities for directly driving leds while consuming low device current. one hardware pin (addr) can be used to program and vary the fixed i 2 c-bus address and allow up to two devices to share the same i 2 c-bus or smbus. 2. features and benefits ? i 2 c-bus to parallel port expander ? operating power supply voltage range of 1.65 v to 5.5 v ? allows bidirectional voltage-level tr anslation and gpio expansion between: ? 1.8v scl/sda and 1.8v, 2.5v, 3.3v or 5v portp ? 2.5v scl/sda and 1.8v, 2.5v, 3.3v or 5v portp ? 3.3v scl/sda and 1.8v, 2.5v, 3.3v or 5v portp ? 5v scl/sda and 1.8v, 2.5v, 3.3v or 5v portp ? low standby current consumption of 1 ? a ? schmitt-trigger action allows slow input tran sition and better switching noise immunity at the scl and sda inputs ? v hys = 0.18 v (typical) at 1.8 v ? v hys = 0.25 v (typical) at 2.5 v ? v hys = 0.33 v (typical) at 3.3 v ? v hys = 0.5 v (typical) at 5 v ? 5 v tolerant i/o ports ? active low reset input (reset ) ? open-drain active low interrupt output (int ) ? 400 khz fast-mode i 2 c-bus ? input/output configuration register ? polarity inversion register ? internal power-on reset ? power-up with all channels configured as inputs ? no glitch on power-up ? noise filter on scl/sda inputs ? latched outputs with 25 ma drive maximu m capability for directly driving leds ? latch-up performance exceeds 100 ma per jesd 78, class ii ? esd protection exceeds jesd 22 ? 2000 v human-body model (a114-a) ? 1000 v charged-device model (c101) ? packages offered: hvqf n16, tssop16, xqfn16
pca6408a all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2012. all rights reserved. product data sheet rev. 1 ? 27 september 2012 3 of 40 nxp semiconductors pca6408a low-voltage, 8-bit i 2 c-bus and smbus i/o expander 3. ordering information 3.1 ordering options 4. block diagram table 1. ordering information type number topside mark package name description version pca6408abs p8a hvqfn16 plastic thermal enhanced very thin quad flat package; no leads; 16 terminals; body 3 ? 3 ? 0.85 mm sot758-1 pca6408apw pa6408a tssop16 plastic thin shrink small outline package; 16 leads; body width 4.4 mm sot403-1 PCA6408AHK p8 xqfn16 plastic, extremely thin quad flat package; no leads; 16 terminals; body 1.80 ? 2.60 ? 0.50 mm sot1161-1 table 2. ordering options type number orderable part number package packing method minimum order quantity temperature pca6408abs pca6408abshp hvq fn16 reel pack, smd, 13-inch, turned 6000 t amb = ? 40 ? c to +85 ?c pca6408apw pca6408apw,118 t ssop16 reel pack, smd, 13-inch 2500 t amb = ? 40 ? c to +85 ?c PCA6408AHK PCA6408AHKx xqfn16 reel pack, smd 4000 t amb = ? 40 ? c to +85 ?c all i/os are set to inputs at reset. fig 1. block diagram (positive logic) 002aaf823 int i 2 c-bus control interrupt logic pca6408a lp filter addr input filter shift register sda scl 8 bits write pulse read pulse power-on reset v dd(p) v ss i/o port p0 to p7 reset v dd(i2c-bus)
pca6408a all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2012. all rights reserved. product data sheet rev. 1 ? 27 september 2012 4 of 40 nxp semiconductors pca6408a low-voltage, 8-bit i 2 c-bus and smbus i/o expander 5. pinning information 5.1 pinning the exposed center pad, if used, must be connected only as a secondary v ss or must be left electrically open. fig 2. pin configuration for tssop16 fig 3. pin configuration for hvqfn16 fig 4. pin configuration for xqfn16 pca6408apw v dd(i2c-bus) v dd(p) addr sda reset scl p0 int p1 p7 p2 p6 p3 p5 v ss p4 002aaf821 1 2 3 4 5 6 7 8 10 9 12 11 14 13 16 15 002aaf830 transparent top view p6 p7 scl p3 v ss p4 p5 addr v dd(i2c-bus) v dd(p) sda 4 9 3 10 2 11 1 12 5 6 7 8 16 15 14 13 terminal 1 index area reset p0 int p1 p2 pca6408abs PCA6408AHK terminal 1 index area 002aaf822 transparent top view 8p5 7p4 6v ss 5p3 sda 13 v dd(p) 14 v dd(i2c-bus) 15 addr16 scl 12 int 11 p7 10 p69 1reset 2p0 3p1 4p2
pca6408a all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2012. all rights reserved. product data sheet rev. 1 ? 27 september 2012 5 of 40 nxp semiconductors pca6408a low-voltage, 8-bit i 2 c-bus and smbus i/o expander 5.2 pin description [1] all i/o are configured as input at power-on. table 3. pin description symbol pin description tssop16 hvqfn16 xqfn16 v dd(i2c-bus) 1 15 15 supply voltage of i 2 c-bus. connect directly to the v dd of the external i 2 c master. provides voltage-level translation. addr 2 16 16 address input. connect directly to v dd(p) or ground. reset 3 1 1 active low reset input. connect to v dd(i2c-bus) through a pull-up resistor if no active connection is used. p0 [1] 4 2 2 port p input/output 0. p1 [1] 5 3 3 port p input/output 1. p2 [1] 6 4 4 port p input/output 2. p3 [1] 7 5 5 port p input/output 3. v ss 8 6 6 ground. p4 [1] 9 7 7 port p input/output 4. p5 [1] 10 8 8 port p input/output 5. p6 [1] 11 9 9 port p input/output 6. p7 [1] 12 10 10 port p input/output 7. int 13 11 11 interrupt output. connect to v dd(i2c-bus) through a pull-up resistor. scl 14 12 12 serial clock bus. connect to v dd(i2c-bus) through a pull-up resistor. sda 15 13 13 serial data bus. connect to v dd(i2c-bus) through a pull-up resistor. v dd(p) 16 14 14 supply voltage of pca6408a for port p.
pca6408a all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2012. all rights reserved. product data sheet rev. 1 ? 27 september 2012 6 of 40 nxp semiconductors pca6408a low-voltage, 8-bit i 2 c-bus and smbus i/o expander 6. voltage translation ta b l e 4 shows how to set up v dd levels for the necessary voltage translation between the i 2 c-bus and the pca6408a. 7. functional description refer to figure 1 ? block diagram (positive logic) ? . 7.1 device address the address of the pca6408a is shown in figure 5 . addr is the hardware address package pin and is held to either high (logic 1) or low (logic 0) to assign one of the two possible sl ave addresses. the last bit of the slave address defines the operation (read or write) to be performed. a high (logic 1) selects a read operation, while a low (logic 0) selects a write operation. table 4. voltage translation v dd(i2c-bus) (sda and scl of i 2 c master) v dd(p) (port p) 1.8 v 1.8 v 1.8 v 2.5 v 1.8 v 3.3 v 1.8v 5v 2.5 v 1.8 v 2.5 v 2.5 v 2.5 v 3.3 v 2.5v 5v 3.3 v 1.8 v 3.3 v 2.5 v 3.3 v 3.3 v 3.3v 5v 5v 1.8v 5v 2.5v 5v 3.3v 5v 5v fig 5. pca6408a address r/w 002aaf539 0 1 0 0 0 0 ad dr fixed slave address programmable
pca6408a all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2012. all rights reserved. product data sheet rev. 1 ? 27 september 2012 7 of 40 nxp semiconductors pca6408a low-voltage, 8-bit i 2 c-bus and smbus i/o expander 7.2 interface definition 7.3 pointer register and command byte following the successful acknowledgement of the address byte, the bus master sends a command byte, which is stored in the pointer register in the pca6408a. two bits of this data byte state the operation (read or write) and the internal registers (input, output, polarity inversion, or configur ation) that will be affected. this regist er is write only. [1] undefined. table 5. interface definition byte bit 7 (msb) 6 5 4 3 2 1 0 (lsb) i 2 c-bus slave address l h l l l l addr r/w i/o data bus p7 p6 p5 p4 p3 p2 p1 p0 fig 6. pointer register bits 002aaf540 b7 b6 b5 b4 b3 b2 b1 b0 table 6. command byte pointer register bits command byte (hexadecimal) register protocol power-up default b7 b6 b5 b4 b3 b2 b1 b0 0 0 0 0 0 0 0 0 00h input port read byte xxxx xxxx [1] 0 0 0 0 0 0 0 1 01h output port read/write byte 1111 1111 0 0 0 0 0 0 1 0 02h polarity inversion read/write byte 0000 0000 0 0 0 0 0 0 1 1 03h configuration read/write byte 1111 1111
pca6408a all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2012. all rights reserved. product data sheet rev. 1 ? 27 september 2012 8 of 40 nxp semiconductors pca6408a low-voltage, 8-bit i 2 c-bus and smbus i/o expander 7.4 register descriptions 7.4.1 input port register (00h) the input port register (register 0) reflects th e incoming logic levels of the pins, regardless of whether the pin is defined as an input or an output by the configuration register. the input port register is read only; writes to this register have no effect. the default value ?x? is determined by the externally applied logic le vel. an input port register read operation is performed as described in section 8.2 ? read commands ? . 7.4.2 output port register (01h) the output port register (register 1) shows the outgoing logic levels of the pins defined as outputs by the configuration register. bit values in these registers have no effect on pins defined as inputs. in turn, reads from this regi ster reflect the value th at was written to this register, not the actual pin value. 7.4.3 polarity inversion register (02h) the polarity inversion register (register 2) a llows polarity inversion of pins defined as inputs by the configuration register. if a bit in this register is set (written with ?1?), the corresponding port pin?s polarity is inverted. if a bi t in this register is cleared (written with a ?0?), the corresponding port pin?s original polarity is retained. 7.4.4 configuration register (03h) the configuration register (register 3) configures the direction of the i/o pins. if a bit in this register is set to 1, the corresponding port pin is enabled as a high-impedance input. if a bit in this register is cleared to 0, the corresponding port pin is enabled as an output. table 7. input port register (address 00h) bit 7 6 5 4 3 2 1 0 symbol i7 i6 i5 i4 i3 i2 i1 i0 default xxxxxxxx table 8. output port register (address 01h) bit 7 6 5 4 3 2 1 0 symbol o7 o6 o5 o4 o3 o2 o1 o0 default 11111111 table 9. register 2: polarity inversion register (address 02h) bit 7 6 5 4 3 2 1 0 symbol n7 n6 n5 n4 n3 n2 n1 n0 default 00000000 table 10. register 3: configuration register (address 03h) bit 7 6 5 4 3 2 1 0 symbol c7 c6 c5 c4 c3 c2 c1 c0 default 11111111
pca6408a all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2012. all rights reserved. product data sheet rev. 1 ? 27 september 2012 9 of 40 nxp semiconductors pca6408a low-voltage, 8-bit i 2 c-bus and smbus i/o expander 7.5 i/o port when an i/o is configured as an input, fets q1 and q2 are off, which creates a high-impedance input. the input voltage may be raised above v dd to a maximum of 5.5 v. if the i/o is configured as an output, q1 or q2 is enabled, depending on the state of the output port register. in this case, there are low-impedance paths between the i/o pin and either v dd(p) or v ss . the external voltage applied to this i/o pin should not exceed the recommended levels for proper operation. on power-up or reset, all registers return to default values. fig 7. simplified schematic of p0 to p7 v dd(p) p0 to p7 output port register data configuration register dq ck q data from shift register write configuration pulse output port register dq ck write pulse polarity inversion register dq ck data from shift register write polarity pulse input port register dq ck read pulse input port register data polarity inversion register data 002aaf824 ff data from shift register ff ff ff q1 q2 v ss to int esd protection diode
pca6408a all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2012. all rights reserved. product data sheet rev. 1 ? 27 september 2012 10 of 40 nxp semiconductors pca6408a low-voltage, 8-bit i 2 c-bus and smbus i/o expander 7.6 power-on reset when power (from 0 v) is applied to v dd(p) , an internal power-on reset holds the pca6408a in a reset condition until v dd(p) has reached v por . at that time, the reset condition is released and th e pca6408a registers and i 2 c-bus/smbus state machine initialize to their default states. after that, v dd(p) must be lowered to below v porf and back up to the operating volt age for a power-reset cycle. see section 9.2 ? power-on reset requirements ? . 7.7 reset input (reset ) the reset input can be asserted to initialize the system while keeping the v dd(p) at its operating level. a reset can be accomplished by holding the reset pin low for a minimum of t w(rst) . the pca6408a registers and i 2 c-bus/smbus state machine are changed to their default state once reset is low (0). when reset is high (1), the i/o levels at the p port can be changed externally or through the master. this input requires a pull-up resistor to v dd(i2c-bus) if no active connection is used. 7.8 interrupt output (int ) an interrupt is generated by an y rising or falling edge of t he port inputs in the input mode. after time t v(int) , the signal int is valid. resetting the interrupt circuit is achieved when data on the port is changed to the original setting or when data is read from the port that generated the interrupt (see figure 11 ). resetting occurs in the read mode at the acknowledge (ack) or not acknowledge (nack) bit after the rising edge of the scl signal. interrupts that occur during the ack or nack clock pulse can be lost (or be very short) due to the resetting of the interrupt during this pulse. each change of the i/os after resetting is detected and is transmitted as int . a pin configured as an output cannot cause an interrupt. changing an i/o from an output to an input may cause a false interrupt to occu r, if the state of the pin does not match the contents of the input port register. the int output has an open-drain structure and requires a pull-up resistor to v dd(p) or v dd(i2c-bus) depending on the application. int should be connected to the voltage source of the device that requires the interrupt information.
pca6408a all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2012. all rights reserved. product data sheet rev. 1 ? 27 september 2012 11 of 40 nxp semiconductors pca6408a low-voltage, 8-bit i 2 c-bus and smbus i/o expander 8. bus transactions the pca6408a is an i 2 c-bus slave device. data is exchanged between the master and pca6408a through write and read commands using i 2 c-bus. the two communication lines are a serial data line (sda) and a serial clock line (scl). both lines must be connected to a positive supply via a pull-up re sistor when connected to the output stages of a device. data transfer may be initiated only when the bus is not busy. 8.1 write commands data is transmitted to the pca6408a by sending the device address and setting the least significant bit (lsb) to a logic 0 (see figure 5 for device address). the command byte is sent after the address and determines which register receives the data that follows the command byte. there is no limitation on t he number of data bytes sent in one write transmission. fig 8. write to output port register 0 a s slave address start condition r/w acknowledge from slave 002aaf825 0000001 0 command byte a acknowledge from slave 12345678 scl 9 sda data 1 a write to port data out from port t v(q) acknowledge from slave data 1 valid data to port 10000 ad dr 0 p stop condition fig 9. write to configuration or polarity inversion registers 0 a s slave address start condition r/w acknowledge from slave 002aaf826 0000011/0 0 command byte a acknowledge from slave 12345678 scl 9 sda data 1 a acknowledge from slave data to register 10000 ad dr 0 p stop condition
pca6408a all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2012. all rights reserved. product data sheet rev. 1 ? 27 september 2012 12 of 40 nxp semiconductors pca6408a low-voltage, 8-bit i 2 c-bus and smbus i/o expander 8.2 read commands to read data from the pca6408a, the bus master must first send the pca6408a address with the least significant bit set to a logic 0 (see figure 5 for device address). the command byte is sent after the address and determines which register is to be accessed. after a restart the device address is sent agai n, but this time the lsb is set to a logic 1. data from the register defined by the command byte then is sent by the pca6408a (see figure 10 and figure 11 ). data is clocked into the register on the risi ng edge of the ack clock pulse. there is no limit on the number of data bytes received in one read transmission, but on the final byte received the bus master must not acknowledge the data. fig 10. read from register a s start condition r/w acknowledge from slave 002aaf827 a acknowledge from slave sda a p acknowledge from master data (first byte) slave address stop condition s (repeated) start condition (cont.) (cont.) 10000 ad dr 1 a 0 r/w acknowledge from slave slave address at this moment master-transmitter becomes master-receiver and slave-receiver becomes slave-transmitter na no acknowledge from master 10000 ad dr 0 0 data from register data (last byte) data from register command byte 00000 0 1 1/0 transfer of data can be stopped at any time by a stop condition. when this occurs, data present at the latest acknowledge phase is valid (output mode). it is assumed that the command byte has previously been programmed with 00h (read input port register). this figure eliminates the command byte transfer, a restart, and slave address call between the in itial slave address call and actual data transfer from p port (see figure 10 ). fig 11. read input port register 10000 ad dr 1 a s0 slave address start condition r/w acknowledge from slave 002aaf828 data from port a acknowledge from master sda 1 no acknowledge from master read from port data into port data from port data 1 data 4 int data 4 data 2 data 3 p stop condition t v(int) t rst(int) t h(d) t su(d) 12345678 scl 9 data 1 data 5 int is cleared by read from port stop not needed to clear int
pca6408a all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2012. all rights reserved. product data sheet rev. 1 ? 27 september 2012 13 of 40 nxp semiconductors pca6408a low-voltage, 8-bit i 2 c-bus and smbus i/o expander 9. application design-in information 9.1 minimizing i dd when i/os control leds when the i/os are used to control leds, normally they are connected to v dd(p) through a resistor as shown in figure 12 . the led acts as a diode, so when the led is off, the i/o v i is about 1.2 v less than v dd(p) . the ? i dd parameter in table 15 ? static characteristics ? shows how i dd(p) increases as v i becomes lower than v dd(p) . designs that must minimize current consumption, such as battery power applications, should consider maintaining the i/o pins greater than or equal to v dd(p) when the led is off. figure 13 shows a high-value resistor in parallel with the led. figure 14 shows v dd(p) less than the led supply voltage by at least 1.2 v. both of these methods maintain the i/o v i at or above v dd(p) and prevent additional supply current consumption when the led is off. device address configured as 0100 000x for this example. p0 and p2 through p4 are configured as inputs. p1 and p5 through p7 are configured as outputs. (1) resistors are required for inputs (on p port) that may float. if a driver to an input will never let the input float, a resistor is not needed. outputs (in the p port) do not need pull-up resistors. fig 12. typical application pca6408a p0 p1 scl sda v dd scl sda p2 p3 v ss master controller v ss v dd(i2c-bus) = 1.8 v controlled switch a b enable int v dd(p) int 10 k subsystem 1 (e.g., alarm system) alarm (1) p4 p5 p6 p7 10 k 10 k reset reset v dd(p) 002aaf829 v dd(i2c-bus) v dd(i2c-bus) addr keypad 10 k 10 k ( 3)
pca6408a all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2012. all rights reserved. product data sheet rev. 1 ? 27 september 2012 14 of 40 nxp semiconductors pca6408a low-voltage, 8-bit i 2 c-bus and smbus i/o expander 9.2 power-on reset requirements in the event of a glitch or data corruption, pca6408a can be reset to its default conditions by using the power-on reset feature. power-on reset requires that the device go through a power cycle to be complete ly reset. this reset also happens when the device is powered on for the first time in an application. the two types of power-on reset are shown in figure 15 and figure 16 . ta b l e 11 specifies the performance of the power- on reset feature for pca6408a for both types of power-on reset. fig 13. high-value resistor in parallel with the led fig 14. device supplied by a lower voltage 002aah278 led v dd(p) pn 100 k v dd 002aah279 led v dd(p) pn 3.3 v 5 v fig 15. v dd(p) is lowered below 0.2 v or 0 v and then ramped up to v dd(p) fig 16. v dd(p) is lowered below the por threshold, then ramped back up to v dd(p) 002aag960 v dd(p) time ramp-up ramp-down (dv/dt) r (dv/dt) f re-ramp-up (dv/dt) r time to re-ramp when v dd(p) drops below 0.2 v or to v ss t d(rst) 002aag961 v dd(p) time ramp-down (dv/dt) f ramp-up (dv/dt) r time to re-ramp when v dd(p) drops to v por(min) ? 50 mv t d(rst) v i drops below por levels
pca6408a all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2012. all rights reserved. product data sheet rev. 1 ? 27 september 2012 15 of 40 nxp semiconductors pca6408a low-voltage, 8-bit i 2 c-bus and smbus i/o expander [1] level that v dd(p) can glitch down to with a ramp rate of 0.4 ? s/v, but not cause a functional disruption when t w(gl)vdd <1 ? s. [2] glitch width that will not cause a functional disruption when ? v dd(gl) =0.5 ? v dd(p) . glitches in the power supply can also affect the power-on reset performance of this device. the glitch width (t w(gl)vdd ) and glitch height ( ? v dd(gl) ) are dependent on each other. the bypass capacitance, source impedan ce, and device impedance are factors that affect power-on reset performance. figure 17 and ta b l e 11 provide more information on how to measure thes e specifications. v por is critical to the power-on reset. v por is the voltage level at which the reset condition is released and all the registers and the i 2 c-bus/smbus state machine are initialized to their default states. the value of v por differs based on the v dd(p) being lowered to or from 0v. figure 18 and ta b l e 11 provide more details on this specification. table 11. recommended supply sequencing and ramp rates t amb =25 ? c (unless otherwise noted). not tested; specified by design. symbol parameter condition min typ max unit (dv/dt) f fall rate of change of voltage figure 15 0.1 - 2000 ms (dv/dt) r rise rate of change of voltage figure 15 0.1 - 2000 ms t d(rst) reset delay time figure 15 ; re-ramp time when v dd(p) drops to v ss 1- - ? s figure 16 ; re-ramp time when v dd(p) drops to v por(min) ? 50 mv 1- - ? s ? v dd(gl) glitch supply voltage difference figure 17 [1] --1.0v t w(gl)vdd supply voltage glitch pulse width figure 17 [2] --10 ? s v por(trip) power-on reset trip voltage falling v dd(p) 0.7--v rising v dd(p) --1.4v fig 17. glitch width and glitch height fig 18. power-on reset voltage (v por ) 002aag962 v dd(p) time t w(gl)vdd ?v dd(gl) 002aag963 por time v dd(p) time v por (rising v dd(p) ) v por (falling v dd(p) )
pca6408a all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2012. all rights reserved. product data sheet rev. 1 ? 27 september 2012 16 of 40 nxp semiconductors pca6408a low-voltage, 8-bit i 2 c-bus and smbus i/o expander 10. limiting values [1] the input negative-voltage and output voltage ratings may be exceeded if the input and output current ratings are observed. 11. recommended operating conditions table 12. limiting values in accordance with the absolute ma ximum rating system (iec 60134). symbol parameter conditions min max unit v dd(i2c-bus) i 2 c-bus supply voltage ? 0.5 +6.5 v v dd(p) supply voltage port p ? 0.5 +6.5 v v i input voltage [1] ? 0.5 +6.5 v v o output voltage [1] ? 0.5 +6.5 v i ik input clamping current addr, reset , scl; v i <0v - ? 20 ma i ok output clamping current int ; v o <0v - ? 20 ma i iok input/output clamping current p port; v o <0vorv o >v dd(p) - ? 20 ma sda; v o <0vorv o >v dd(i2c-bus) - ? 20 ma i ol low-level output current continuous; p port; v o = 0 v to v dd(p) -50ma continuous; sda, int ; v o = 0 v to v dd(i2c-bus) -25ma i oh high-level output current continuous; p port; v o = 0 v to v dd(p) -25ma i dd supply current continuous through v ss - 200 ma i dd(p) supply current port p continuous through v dd(p) - 160 ma i dd(i2c-bus) i 2 c-bus supply current continuous through v dd(i2c-bus) -10ma t stg storage temperature ? 65 +150 ?c t j(max) maximum junction temperature - 125 ?c table 13. operating conditions symbol parameter conditions min max unit v dd(i2c-bus) i 2 c-bus supply voltage 1.65 5.5 v v dd(p) supply voltage port p 1.65 5.5 v v ih high-level input volt age scl, sda, reset 0.7 ? v dd(i2c-bus) 5.5 v addr, p7 to p0 0.7 ? v dd(p) 5.5 v v il low-level input voltage scl, sda, reset ? 0.5 0.3 ? v dd(i2c-bus) v addr, p7 to p0 ? 0.5 0.3 ? v dd(p) v i oh high-level output current p7 to p0 - 10 ma i ol low-level output current p7 to p0 - 25 ma t amb ambient temperature operating in free air ? 40 +85 ?c
pca6408a all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2012. all rights reserved. product data sheet rev. 1 ? 27 september 2012 17 of 40 nxp semiconductors pca6408a low-voltage, 8-bit i 2 c-bus and smbus i/o expander 12. thermal characteristics [1] the package thermal impedance is calculated in accordance with jesd 51-7. 13. static characteristics table 14. thermal characteristics symbol parameter conditions max unit z th(j-a) transient thermal impedance from junction to ambient tssop16 package [1] 108 k/w hvqfn16 package [1] 53 k/w xqfn16 package [1] 184 k/w table 15. static characteristics t amb = ? 40 ? c to +85 ? c; v dd(i2c-bus) = 1.65 v to 5.5 v; unless otherwise specified. symbol parameter conditions min typ [1] max unit v ik input clamping voltage i i = ? 18 ma ? 1.2 - - v v por power-on reset voltage v i =v dd(p) or v ss ; i o =0ma - 1.1 1.4 v v oh high-level output voltage pport i oh = ? 8ma; v dd(p) =1.65v [2] 1.2 - - v i oh = ? 10 ma; v dd(p) =1.65v [2] 1.1 - - v i oh = ? 8ma; v dd(p) =2.3v [2] 1.8 - - v i oh = ? 10 ma; v dd(p) =2.3v [2] 1.7 - - v i oh = ? 8ma; v dd(p) =3.0v [2] 2.6 - - v i oh = ? 10 ma; v dd(p) =3.0v [2] 2.5 - - v i oh = ? 8ma; v dd(p) =4.5v [2] 4.1 - - v i oh = ? 10 ma; v dd(p) =4.5v [2] 4.0 - - v v ol low-level output voltage p port; i ol =8ma v dd(p) =1.65v [2] - - 0.45 v v dd(p) =2.3v [2] - - 0.25 v v dd(p) =3v [2] - - 0.25 v v dd(p) =4.5v [2] -- 0.2v i ol low-level output current v ol = 0.4 v; v dd(p) =1.65v to 5.5v sda [3] 3- - ma int [3] 315 [4] -ma p port v ol = 0.5 v; v dd(p) =1.65v [3] 810- ma v ol = 0.7 v; v dd(p) =1.65v [3] 10 13 - ma v ol = 0.5 v; v dd(p) =2.3v [3] 810- ma v ol = 0.7 v; v dd(p) =2.3v [3] 10 13 - ma v ol = 0.5 v; v dd(p) =3.0v [3] 814- ma v ol = 0.7 v; v dd(p) =3.0v [3] 10 19 - ma v ol = 0.5 v; v dd(p) =4.5v [3] 817- ma v ol = 0.7 v; v dd(p) =4.5v [3] 10 24 - ma
pca6408a all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2012. all rights reserved. product data sheet rev. 1 ? 27 september 2012 18 of 40 nxp semiconductors pca6408a low-voltage, 8-bit i 2 c-bus and smbus i/o expander [1] for i dd , all typical values are at nominal supply voltage (1.8 v, 2.5 v, 3.3 v, 3.6 v or 5 v v dd ) and t amb =25 ? c. except for i dd , the typical values are at v dd(p) =v dd(i2c-bus) = 3.3 v and t amb =25 ? c. [2] the total current sourced by all i/os must be limited to 80 ma. [3] each i/o must be externally limited to a maximum of 25 ma, for a device total of 200 ma. [4] typical value for t amb =25 ? c. v ol = 0.4 v and v dd = 3.3 v. typical value for v dd <2.5v, v ol =0.6v. i i input current v dd(p) = 1.65 v to 5.5 v scl, sda, reset ; v i =v dd(i2c-bus) or v ss -- ? 1 ? a addr; v i =v dd(p) or v ss -- ? 1 ? a i ih high-level input current p port; v i =v dd(p) ; v dd(p) = 1.65 v to 5.5 v - - 1 ? a i il low-level input current p port; v i =v ss ; v dd(p) = 1.65 v to 5.5 v - - 1 ? a i dd supply current i dd(i2c-bus) +i dd(p) ; sda, p port, addr, reset ; v i on sda and reset =v dd(i2c-bus) or v ss ; v i on p port and addr = v dd(p) ; i o =0ma;i/o=inputs; f scl = 400 khz v dd(p) = 3.6 v to 5.5 v - 10 25 ? a v dd(p) = 2.3 v to 3.6 v - 6.5 15 ? a v dd(p) = 1.65 v to 2.3 v - 4 9 ? a i dd(i2c-bus) +i dd(p) ; scl, sda, p port, addr, reset ; v i on scl, sda and reset =v dd(i2c-bus) or v ss ; v i on p port and addr = v dd(p) ; i o =0ma;i/o=inputs; f scl = 0 khz v dd(p) = 3.6 v to 5.5 v - 1.5 7 ? a v dd(p) = 2.3 v to 3.6 v - 1 3.2 ? a v dd(p) = 1.65 v to 2.3 v - 0.5 1.7 ? a active mode; i dd(i2c-bus) +i dd(p) ; p port, addr, reset ; v i on reset =v dd(i2c-bus) ; v i on p port and addr = v dd(p) ; i o =0ma;i/o=inputs; f scl = 400 khz, continuous register read v dd(p) = 3.6 v to 5.5 v - 60 125 ? a v dd(p) = 2.3 v to 3.6 v - 40 75 ? a v dd(p) = 1.65 v to 2.3 v - 20 45 ? a ? i dd additional quiescent supply current scl, sda, reset ; one input at v dd(i2c-bus) ? 0.6 v, other inputs at v dd(i2c-bus) or v ss ; v dd(p) =1.65vto5.5v -- 25 ? a p port, addr; one input at v dd(p) ? 0.6 v, other inputs at v dd(p) or v ss ; v dd(p) =1.65vto5.5v -- 80 ? a c i input capacitance v i =v dd(i2c-bus) or v ss ; v dd(p) = 1.65 v to 5.5 v - 6 7 pf c io input/output capacitance v i/o =v dd(i2c-bus) or v ss ; v dd(p) =1.65vto5.5v - 7 8 pf v i/o =v dd(p) or v ss ; v dd(p) = 1.65 v to 5.5 v - 7.5 8.5 pf table 15. static characteristics ?continued t amb = ? 40 ? c to +85 ? c; v dd(i2c-bus) = 1.65 v to 5.5 v; unless otherwise specified. symbol parameter conditions min typ [1] max unit
pca6408a all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2012. all rights reserved. product data sheet rev. 1 ? 27 september 2012 19 of 40 nxp semiconductors pca6408a low-voltage, 8-bit i 2 c-bus and smbus i/o expander 13.1 typical characteristics i dd = i dd(i2c-bus) + i dd(p) fig 19. supply current versus ambient temperature fig 20. standby supply current versus ambient temperature t amb =25 ? c i dd = i dd(i2c-bus) + i dd(p) fig 21. supply current versus supply voltage 8 12 4 16 20 i dd (a) 0 t amb (c) ?40 85 60 10 35 ?15 002aag973 v dd(p) = 5.5 v 5.0 v 3.6 v 3.3 v 2.5 v 2.3 v v dd(p) = 1.8 v 1.65 v 600 800 400 1400 i dd(stb) (na) 0 t amb (c) ?40 85 60 10 35 ?15 002aag974 v dd(p) = 5.5 v 5.0 v 3.6 v 3.3 v 200 1000 2.5 v 2.3 v 1.8 v 1.65 v 8 12 4 16 20 i dd (a) 0 v dd(p) (v) 1.5 5.5 4.5 2.5 3.5 002aag975
pca6408a all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2012. all rights reserved. product data sheet rev. 1 ? 27 september 2012 20 of 40 nxp semiconductors pca6408a low-voltage, 8-bit i 2 c-bus and smbus i/o expander a. v dd(p) =1.65v b. v dd(p) =1.8v c. v dd(p) =2.5v d. v dd(p) =3.3v e. v dd(p) =5.0v f. v dd(p) =5.5v fig 22. i/o sink current versus low-level output voltage v ol (v) 0 0.3 0.2 0.1 002aaf578 15 25 35 i sink (ma) 0 t amb = ?40 c 25 c 85 c 5 10 20 30 v ol (v) 0 0.3 0.2 0.1 002aaf579 15 25 35 i sink (ma) 0 t amb = ?40 c 25 c 85 c 5 10 20 30 v ol (v) 0 0.3 0.2 0.1 002aaf580 20 50 i sink (ma) 0 t amb = ?40 c 25 c 85 c 10 30 40 v ol (v) 0 0.3 0.2 0.1 002aaf581 20 40 60 i sink (ma) 0 t amb = ?40 c 25 c 85 c v ol (v) 0 0.3 0.2 0.1 002aaf582 30 50 70 i sink (ma) 0 t amb = ?40 c 25 c 85 c 10 20 40 60 v ol (v) 0 0.3 0.2 0.1 002aaf583 30 50 70 i sink (ma) 0 t amb = ?40 c 25 c 85 c 10 20 40 60
pca6408a all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2012. all rights reserved. product data sheet rev. 1 ? 27 september 2012 21 of 40 nxp semiconductors pca6408a low-voltage, 8-bit i 2 c-bus and smbus i/o expander a. v dd(p) =1.65v b. v dd(p) =1.8v c. v dd(p) =2.5v d. v dd(p) =3.3v e. v dd(p) =5.0v f. v dd(p) =5.5v fig 23. i/o source current versus high-level output voltage v dd(p) ? v oh (v) 0 0.6 0.4 0.2 002aaf561 10 20 30 i source (ma) 0 t amb = ?40 c 25 c 85 c v dd(p) ? v oh (v) 0 0.6 0.4 0.2 002aaf562 15 25 35 i source (ma) 0 t amb = ?40 c 25 c 85 c 5 10 20 30 v dd(p) ? v oh (v) 0 0.6 0.4 0.2 002aaf563 20 40 60 i source (ma) 0 t amb = ?40 c 25 c 85 c v dd(p) ? v oh (v) 0 0.6 0.4 0.2 002aaf564 30 50 70 i source (ma) 0 t amb = ?40 c 25 c 85 c 10 20 40 60 v dd(p) ? v oh (v) 0 0.6 0.4 0.2 002aaf565 30 60 90 i source (ma) 0 t amb = ?40 c 25 c 85 c v dd(p) ? v oh (v) 0 0.6 0.4 0.2 002aaf566 30 60 90 i source (ma) 0 t amb = ?40 c 25 c 85 c
pca6408a all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2012. all rights reserved. product data sheet rev. 1 ? 27 september 2012 22 of 40 nxp semiconductors pca6408a low-voltage, 8-bit i 2 c-bus and smbus i/o expander (1) v dd(p) = 1.8 v; i sink =10ma (2) v dd(p) = 5 v; i sink =10ma (3) v dd(p) = 1.8 v; i sink =1ma (4) v dd(p) = 5 v; i sink =1ma i source = ? 10 ma fig 24. low-level output voltage versus temperature fig 25. i/o high voltage versus temperature 60 80 20 100 120 v ol (mv) 0 t amb (c) ?40 85 60 10 35 ?15 002aah056 (1) (3) (4) (2) 40 t amb (c) ?40 85 60 10 35 ?15 002aah057 160 120 200 0 v dd(p) ? v oh (mv) v dd(p) = 1.8 v 5 v 80 40
pca6408a all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2012. all rights reserved. product data sheet rev. 1 ? 27 september 2012 23 of 40 nxp semiconductors pca6408a low-voltage, 8-bit i 2 c-bus and smbus i/o expander 14. dynamic characteristics table 16. i 2 c-bus interface timing requirements over recommended operating free air temperat ure range, unless otherwise specified. see figure 26 . symbol parameter conditions standard-mode i 2 c-bus fast-mode i 2 c-bus unit min max min max f scl scl clock frequency 0 100 0 400 khz t high high period of the scl clock 4 - 0.6 - ? s t low low period of the scl clock 4.7 - 1.3 - ? s t sp pulse width of spikes that must be suppressed by the input filter 0 50 0 50 ns t su;dat data set-up time 250 - 100 - ns t hd;dat data hold time 0 - 0 - ns t r rise time of both sda and scl signals - 1000 20 300 ns t f fall time of both sda and scl signals - 300 20 ? (v dd /5.5v) 300 ns t buf bus free time between a stop and start condition 4.7 - 1.3 - ? s t su;sta set-up time for a repeated start condition 4.7 - 0.6 - ? s t hd;sta hold time (repeated) start condition 4 - 0.6 - ? s t su;sto set-up time for stop condition 4 - 0.6 - ? s t vd;dat data valid time scl low to sda output valid -3.45 - 0.9 ? s t vd;ack data valid acknowledge time ack signal from scl low to sda (out) low -3.45 - 0.9 ? s table 17. reset timing requirements over recommended operating free air temperat ure range, unless otherwise specified. see figure 29 . symbol parameter conditions standard-mode i 2 c-bus fast-mode i 2 c-bus unit min max min max t w(rst) reset pulse width 30 - 30 - ns t rec(rst) reset recovery time 200 - 200 - ns t rst reset time 600 - 600 - ns
pca6408a all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2012. all rights reserved. product data sheet rev. 1 ? 27 september 2012 24 of 40 nxp semiconductors pca6408a low-voltage, 8-bit i 2 c-bus and smbus i/o expander 15. parameter measure ment information table 18. switching characteristics over recommended operating free air temperature range; c l ? 100 pf; unless other wise specified. see figure 28 . symbol parameter conditions standard-mode i 2 c-bus fast-mode i 2 c-bus unit min max min max t v(int) valid time on pin int from p port to int -1-1 ? s t rst(int) reset time on pin int from scl to int -1-1 ? s t v(q) data output valid time from scl to p port - 400 - 400 ns t su(d) data input set-up time from p port to scl 0 - 0 - ns t h(d) data input hold time from p port to scl 300 - 300 - ns a. sda load configuration b. transaction format c. voltage waveforms c l includes probe and jig capacitance. t f(o) is measured with c l of 10 pf or 400 pf. all inputs are supplied by generators havi ng the following characteristics: prr ? 10 mhz; z o =50 ? ; t r /t f ? 30 ns. all parameters and waveforms ar e not applicable to all devices. byte 1 = i 2 c-bus address; byte 2 = input register port data. (1) see figure 11 . fig 26. i 2 c-bus interface load circuit and voltage waveforms 002aag977 dut c l = 50 pf r l = 1 k sda v dd(i2c-bus) stop condition (p) data bit 0 (lsb) data bit 7 (msb) ack (a) r/w bit 0 (lsb) address bit 1 address bit 7 (msb) start condition (s) stop condition (p) two bytes for read input port register (1) 002aag952 t low t high t r t f 0.7 v dd(i2c-bus) 0.3 v dd(i2c-bus) 0.7 v dd(i2c-bus) 0.3 v dd(i2c-bus) t sp t buf t f t hd;sta t r scl sda t su;dat t hd;dat t f(o) t vd;ack t vd;dat t vd;ack t su;sta t su;sto 002aag978 repeat start condition stop condition
pca6408a all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2012. all rights reserved. product data sheet rev. 1 ? 27 september 2012 25 of 40 nxp semiconductors pca6408a low-voltage, 8-bit i 2 c-bus and smbus i/o expander a. interrupt load configuration b. voltage waveforms c l includes probe and jig capacitance. all inputs are supplied by generators havi ng the following characteristics: prr ? 10 mhz; z o =50 ? ; t r /t f ? 30 ns. all parameters and waveforms ar e not applicable to all devices. fig 27. interrupt load circuit and voltage waveforms 002aag979 dut c l = 100 pf r l = 4.7 k int v dd(i2c-bus) 10000 ad dr 1 a s0 slave address start condition r/w acknowledge from slave 002aag980 8 bits (one data byte) from port a acknowledge from slave sda 1 no acknowledge from master data into port data from port data 1 data 2 int data 2 data 1 p stop condition t v(int) t rst(int) t su(d) 12345678 scl 9 address t rst(int) a a view a - a int pn t v(int) 0.5 v dd(i2c-bus) 0.5 v dd(p) view b - b scl 0.5 v dd(i2c-bus) int r/w a t rst(int) 0.3 v dd(i2c-bus) 0.7 v dd(i2c-bus) b b
pca6408a all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2012. all rights reserved. product data sheet rev. 1 ? 27 september 2012 26 of 40 nxp semiconductors pca6408a low-voltage, 8-bit i 2 c-bus and smbus i/o expander a. p port load configuration b. write mode (r/w =0) c. read mode (r/w =1) c l includes probe and jig capacitance. t v(q) is measured from 0.7 ? v dd on scl to 50 % i/o (pn) output. all inputs are supplied by generators havi ng the following characteristics: prr ? 10 mhz; z o =50 ? ; t r /t f ? 30 ns. the outputs are measured one at a time, with one transition per measurement. all parameters and waveforms ar e not applicable to all devices. fig 28. p port load circuit and voltage waveforms 002aag981 dut c l = 50 pf 500 pn 2 v dd(p) 500 002aag982 scl sda p0 a t v(q) 0.3 v dd(i2c-bus) 0.7 v dd(i2c-bus) p7 last stable bit unstable data pn 002aag983 scl pn p0 a t h(d) 0.3 v dd(i2c-bus) 0.7 v dd(i2c-bus) p7 0.5 v dd(p) t su(d)
pca6408a all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2012. all rights reserved. product data sheet rev. 1 ? 27 september 2012 27 of 40 nxp semiconductors pca6408a low-voltage, 8-bit i 2 c-bus and smbus i/o expander a. sda load configuration b. p port load configuration c. reset timing c l includes probe and jig capacitance. all inputs are supplied by generators havi ng the following characteristics: prr ? 10 mhz; z o =50 ? ; t r /t f ? 30 ns. the outputs are measured one at a time, with one transition per measurement. i/os are configured as inputs. all parameters and waveforms ar e not applicable to all devices. fig 29. reset load circuits and voltage waveforms 002aag977 dut c l = 50 pf r l = 1 k sda v dd(i2c-bus) 002aag981 dut c l = 50 pf 500 pn 2 v dd(p) 500 sda scl 002aag984 t rst t rec(rst) t w(rst) reset pn start t rst ack or read cycle 0.3 v dd(i2c-bus) 0.5 v dd(i2c-bus) 0.5 v dd(p) t rec(rst)
pca6408a all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2012. all rights reserved. product data sheet rev. 1 ? 27 september 2012 28 of 40 nxp semiconductors pca6408a low-voltage, 8-bit i 2 c-bus and smbus i/o expander 16. package outline fig 30. package outline sot403-1 (tssop16) unit a 1 a 2 a 3 b p cd (1) e (2) (1) eh e ll p qz ywv references outline version european projection issue date iec jedec jeita mm 0.15 0.05 0.95 0.80 0.30 0.19 0.2 0.1 5.1 4.9 4.5 4.3 0.65 6.6 6.2 0.4 0.3 0.40 0.06 8 0 o o 0.13 0.1 0.2 1 dimensions (mm are the original dimensions) notes 1. plastic or metal protrusions of 0.15 mm maximum per side are not included. 2. plastic interlead protrusions of 0.25 mm maximum per side are not included. 0.75 0.50 sot403-1 mo-153 99-12-27 03-02-18 w m b p d z e 0.25 18 16 9 a a 1 a 2 l p q detail x l (a ) 3 h e e c v m a x a y 0 2.5 5 mm scale tssop16: plastic thin shrink small outline package; 16 leads; body width 4.4 mm sot403-1 a max. 1.1 pin 1 index
pca6408a all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2012. all rights reserved. product data sheet rev. 1 ? 27 september 2012 29 of 40 nxp semiconductors pca6408a low-voltage, 8-bit i 2 c-bus and smbus i/o expander fig 31. package outline sot758-1 (hvqfn16) terminal 1 index area 0.5 1 a 1 e h b unit y e 0.2 c references outline version european projection issue date iec jedec jeita mm 3.1 2.9 d h 1.75 1.45 y 1 3.1 2.9 1.75 1.45 e 1 1.5 e 2 1.5 0.30 0.18 0.05 0.00 0.05 0.1 dimensions (mm are the original dimensions) sot758-1 mo-220 - - - - - - 0.5 0.3 l 0.1 v 0.05 w 0 2.5 5 mm scale sot758-1 hvqfn16: plastic thermal enhanced very thin quad flat package; no leads; 16 terminals; body 3 x 3 x 0.85 mm a (1) max. a a 1 c detail x y y 1 c e l e h d h e e 1 b 58 16 13 12 9 4 1 x d e c b a e 2 02-03-25 02-10-21 terminal 1 index area 1/2 e 1/2 e ac c b v m w m e (1) note 1. plastic or metal protrusions of 0.075 mm maximum per side are not included. d (1)
pca6408a all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2012. all rights reserved. product data sheet rev. 1 ? 27 september 2012 30 of 40 nxp semiconductors pca6408a low-voltage, 8-bit i 2 c-bus and smbus i/o expander fig 32. package outline sot1161-1 (xqfn16) references outline version european projection issue date iec jedec jeita sot1161-1 - - - - - - - - - sot1161-1_po 09-12-28 09-12-29 unit (1) mm max nom min 0.5 0.05 0.00 0.25 0.20 0.15 1.9 1.8 1.7 2.7 2.6 2.5 0.4 1.2 0.45 0.40 0.35 0.1 a dimensions note 1. plastic or metal protrusions of 0.075 mm maximum per side are not included. xqfn16: plastic, extremely thin quad flat package; no leads; 16 terminals; body 1.80 x 2.60 x 0.50 mm sot1161-1 a 1 a 3 0.127 bdeee 1 1.2 e 2 ll 1 0.55 0.50 0.45 vw 0.05 y 0.05 y 1 0.05 0 1 2 mm scale b a terminal 1 index area d e x c y c y 1 detail x a a 1 a 3 terminal 1 index area b e 2 e 1 ac b v c w l l 1 5 8 16 13 9 12 4 1 e e
pca6408a all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2012. all rights reserved. product data sheet rev. 1 ? 27 september 2012 31 of 40 nxp semiconductors pca6408a low-voltage, 8-bit i 2 c-bus and smbus i/o expander 17. soldering of smd packages this text provides a very brief insight into a complex technology. a more in-depth account of soldering ics can be found in application note an10365 ?surface mount reflow soldering description? . 17.1 introduction to soldering soldering is one of the most common methods through which packages are attached to printed circuit boards (pcbs), to form electr ical circuits. the soldered joint provides both the mechanical and the electrical connection. th ere is no single sold ering method that is ideal for all ic packages. wave soldering is often preferred when through-hole and surface mount devices (smds) are mixed on one printed wiring board; however, it is not suitable for fine pitch smds. reflow soldering is ideal for the small pitches and high densities that come with increased miniaturization. 17.2 wave and reflow soldering wave soldering is a joining technology in which the joints are made by solder coming from a standing wave of liquid solder. the wave soldering process is suitable for the following: ? through-hole components ? leaded or leadless smds, which are glued to the surface of the printed circuit board not all smds can be wave soldered. packages with solder balls, and some leadless packages which have solder lands underneath the body, cannot be wave soldered. also, leaded smds with leads having a pitch smaller than ~0.6 mm cannot be wave soldered, due to an increased pr obability of bridging. the reflow soldering process involves applying solder paste to a board, followed by component placement and exposure to a temperature profile. leaded packages, packages with solder balls, and leadless packages are all reflow solderable. key characteristics in both wave and reflow soldering are: ? board specifications, in cluding the board finish , solder masks and vias ? package footprints, including solder thieves and orientation ? the moisture sensitivit y level of the packages ? package placement ? inspection and repair ? lead-free soldering versus snpb soldering 17.3 wave soldering key characteristics in wave soldering are: ? process issues, such as application of adhe sive and flux, clinching of leads, board transport, the solder wave parameters, and the time during which components are exposed to the wave ? solder bath specifications, including temperature and impurities
pca6408a all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2012. all rights reserved. product data sheet rev. 1 ? 27 september 2012 32 of 40 nxp semiconductors pca6408a low-voltage, 8-bit i 2 c-bus and smbus i/o expander 17.4 reflow soldering key characteristics in reflow soldering are: ? lead-free versus snpb solderi ng; note that a lead-free reflow process usually leads to higher minimum peak temperatures (see figure 33 ) than a snpb process, thus reducing the process window ? solder paste printing issues including smearing, release, and adjusting the process window for a mix of large and small components on one board ? reflow temperature profile; this profile includ es preheat, reflow (in which the board is heated to the peak temperature) and cooling down. it is imperative that the peak temperature is high enough for the solder to make reliable solder joints (a solder paste characteristic). in addition, the peak temperature must be low enough that the packages and/or boards are not damaged. the peak temperature of the package depends on package thickness and volume and is classified in accordance with ta b l e 1 9 and 20 moisture sensitivity precautions, as indicat ed on the packing, must be respected at all times. studies have shown that small packages reach higher temperatures during reflow soldering, see figure 33 . table 19. snpb eutectic process (from j-std-020c) package thickness (mm) package reflow temperature ( ?c) volume (mm 3 ) < 350 ? 350 < 2.5 235 220 ? 2.5 220 220 table 20. lead-free process (from j-std-020c) package thickness (mm) package reflow temperature ( ?c) volume (mm 3 ) < 350 350 to 2000 > 2000 < 1.6 260 260 260 1.6 to 2.5 260 250 245 > 2.5 250 245 245
pca6408a all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2012. all rights reserved. product data sheet rev. 1 ? 27 september 2012 33 of 40 nxp semiconductors pca6408a low-voltage, 8-bit i 2 c-bus and smbus i/o expander for further information on temperature profiles, refer to application note an10365 ?surface mount reflow soldering description? . msl: moisture sensitivity level fig 33. temperature profiles for large and small components 001aac844 temperature time minimum peak temperature = minimum soldering temperature maximum peak temperature = msl limit, damage level peak temperature
pca6408a all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2012. all rights reserved. product data sheet rev. 1 ? 27 september 2012 34 of 40 nxp semiconductors pca6408a low-voltage, 8-bit i 2 c-bus and smbus i/o expander 18. soldering: pcb footprints fig 34. pcb footprint for sot758-1 (hvqfn16); reflow soldering sot758-1 footprint information for reflow soldering of hvqfn16 package dimensions in mm ax ay bx by d slx sly spx spy gx gy hx hy 4.00 4.00 2.20 2.20 p 0.50 0.24 c 0.90 1.50 1.50 0.30 spy tot 0.90 spx tot 0.90 0.30 3.30 3.30 4.25 4.25 nspx nspy 22 sot758-1_fr occupied area solder land plus solder paste solder land solder paste deposit issue date 12-03-07 12-03-08 aybysly ax bx slx gx hx d gy hy (0.105) spx c p 0.025 0.025 spy spx tot spy tot nspx nspy
pca6408a all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2012. all rights reserved. product data sheet rev. 1 ? 27 september 2012 35 of 40 nxp semiconductors pca6408a low-voltage, 8-bit i 2 c-bus and smbus i/o expander fig 35. pcb footprint for sot403-1 (tssop16); reflow soldering dimensions in mm ay by d1 d2 gy hy p1 c gx sot403-1_fr hx sot403-1 solder land occupied area footprint information for reflow soldering of tssop16 package ay by gy c hy hx gx p1 generic footprint pattern refer to the package outline drawing for actual layout p2 (0.125) (0.125) d1 d2 (4x) p2 7.200 4.500 1.350 0.400 0.600 5.600 5.300 7.450 5.800 0.650 0.750
pca6408a all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2012. all rights reserved. product data sheet rev. 1 ? 27 september 2012 36 of 40 nxp semiconductors pca6408a low-voltage, 8-bit i 2 c-bus and smbus i/o expander fig 36. pcb footprint for sot1161-1 (xqfn16); reflow soldering sot1161-1 footprint information for reflow soldering of xqfn16 package sot1161-1_fr occupied area solder land placement area solder resist, 0.0625 around copper solder land plus solder paste dimensions in mm clearance, 0.125 around occupied area 1.8 cu 0.22 cu (16) 1.65 0.4 (12) 1.65 2.1 cu 2.35 0.45 3.15 2.9 cu 0.9 cu 1 cu solder paste deposit, ?0.02 around copper, stencil thickness 0.1
pca6408a all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2012. all rights reserved. product data sheet rev. 1 ? 27 september 2012 37 of 40 nxp semiconductors pca6408a low-voltage, 8-bit i 2 c-bus and smbus i/o expander 19. abbreviations 20. revision history table 21. abbreviations acronym description esd electrostatic discharge fet field-effect transistor gpio general purpose input/output i 2 c-bus inter-integrated circuit bus i/o input/output led light-emitting diode lsb least significant bit msb most significant bit pcb printed-circuit board por power-on reset smbus system management bus table 22. revision history document id release date data sheet status change notice supersedes pca6408a v.1 20120927 product data sheet - -
pca6408a all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2012. all rights reserved. product data sheet rev. 1 ? 27 september 2012 38 of 40 nxp semiconductors pca6408a low-voltage, 8-bit i 2 c-bus and smbus i/o expander 21. legal information 21.1 data sheet status [1] please consult the most recently issued document before initiating or completing a design. [2] the term ?short data sheet? is explained in section ?definitions?. [3] the product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple device s. the latest product status information is available on the internet at url http://www.nxp.com . 21.2 definitions draft ? the document is a draft versi on only. the content is still under internal review and subject to formal approval, which may result in modifications or additions. nxp semiconductors does not give any representations or warranties as to the accuracy or completeness of information included herein and shall hav e no liability for the consequences of use of such information. short data sheet ? a short data sheet is an extract from a full data sheet with the same product type number(s) and title. a short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. for detailed and full information see the relevant full data sheet, which is available on request vi a the local nxp semiconductors sales office. in case of any inconsistency or conflict with the short data sheet, the full data sheet shall prevail. product specification ? the information and data provided in a product data sheet shall define the specification of the product as agreed between nxp semiconductors and its customer , unless nxp semiconductors and customer have explicitly agreed otherwis e in writing. in no event however, shall an agreement be valid in which the nxp semiconductors product is deemed to offer functions and qualities beyond those described in the product data sheet. 21.3 disclaimers limited warranty and liability ? information in this document is believed to be accurate and reliable. however, nxp semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such info rmation. nxp semiconductors takes no responsibility for the content in this document if provided by an information source outside of nxp semiconductors. in no event shall nxp semiconductors be liable for any indirect, incidental, punitive, special or consequential damages (including - without limitation - lost profits, lost savings, business interruption, costs related to the removal or replacement of any products or rework charges) whether or not such damages are based on tort (including negligence), warranty, breach of contract or any other legal theory. notwithstanding any damages that customer might incur for any reason whatsoever, nxp semiconductors? aggregate and cumulative liability towards customer for the products described herein shall be limited in accordance with the terms and conditions of commercial sale of nxp semiconductors. right to make changes ? nxp semiconductors reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. this document supersedes and replaces all information supplied prior to the publication hereof. suitability for use ? nxp semiconductors products are not designed, authorized or warranted to be suitable for use in life support, life-critical or safety-critical systems or equipment, nor in applications where failure or malfunction of an nxp semiconductors product can reasonably be expected to result in personal injury, death or severe property or environmental damage. nxp semiconductors and its suppliers accept no liability for inclusion and/or use of nxp semiconducto rs products in such equipment or applications and therefore such inclusion and/or use is at the customer?s own risk. applications ? applications that are described herein for any of these products are for illustrative purpos es only. nxp semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. customers are responsible for the design and operation of their applications and products using nxp semiconductors products, and nxp semiconductors accepts no liability for any assistance with applications or customer product design. it is customer?s sole responsibility to determine whether the nxp semiconductors product is suitable and fit for the customer?s applications and products planned, as well as fo r the planned application and use of customer?s third party customer(s). customers should provide appropriate design and operating safeguards to minimize the risks associated with their applications and products. nxp semiconductors does not accept any liability related to any default, damage, costs or problem which is based on any weakness or default in the customer?s applications or products, or the application or use by customer?s third party customer(s). customer is responsible for doing all necessary testing for the customer?s applic ations and products using nxp semiconductors products in order to av oid a default of the applications and the products or of the application or use by customer?s third party customer(s). nxp does not accept any liability in this respect. limiting values ? stress above one or more limiting values (as defined in the absolute maximum ratings system of iec 60134) will cause permanent damage to the device. limiting values are stress ratings only and (proper) operation of the device at these or any other conditions above those given in the recommended operating conditions section (if present) or the characteristics sections of this document is not warranted. constant or repeated exposure to limiting values will permanently and irreversibly affect the quality and reliability of the device. terms and conditions of commercial sale ? nxp semiconductors products are sold subject to the gener al terms and conditions of commercial sale, as published at http://www.nxp.com/profile/terms , unless otherwise agreed in a valid written individual agreement. in case an individual agreement is concluded only the terms and conditions of the respective agreement shall apply. nxp semiconductors hereby expressly objects to applying the customer?s general terms and conditions with regard to the purchase of nxp semiconducto rs products by customer. no offer to sell or license ? nothing in this document may be interpreted or construed as an offer to sell products t hat is open for acceptance or the grant, conveyance or implication of any lic ense under any copyrights, patents or other industrial or intellectual property rights. document status [1] [2] product status [3] definition objective [short] data sheet development this document contains data from the objecti ve specification for product development. preliminary [short] data sheet qualification this document contains data from the preliminary specification. product [short] data sheet production this document contains the product specification.
pca6408a all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2012. all rights reserved. product data sheet rev. 1 ? 27 september 2012 39 of 40 nxp semiconductors pca6408a low-voltage, 8-bit i 2 c-bus and smbus i/o expander export control ? this document as well as the item(s) described herein may be subject to export control regu lations. export might require a prior authorization from competent authorities. non-automotive qualified products ? unless this data sheet expressly states that this specific nxp semicon ductors product is automotive qualified, the product is not suitable for automotive use. it is neither qualified nor tested in accordance with automotive testing or application requirements. nxp semiconductors accepts no liabili ty for inclusion and/or use of non-automotive qualified products in automotive equipment or applications. in the event that customer uses t he product for design-in and use in automotive applications to automotive specifications and standards, customer (a) shall use the product without nxp semiconductors? warranty of the product for such automotive applicat ions, use and specifications, and (b) whenever customer uses the product for automotive applications beyond nxp semiconductors? specifications such use shall be solely at customer?s own risk, and (c) customer fully indemnifies nxp semiconductors for any liability, damages or failed product claims resulting from customer design and use of the product for automotive app lications beyond nxp semiconductors? standard warranty and nxp semiconduct ors? product specifications. translations ? a non-english (translated) version of a document is for reference only. the english version shall prevail in case of any discrepancy between the translated and english versions. 21.4 trademarks notice: all referenced brands, produc t names, service names and trademarks are the property of their respective owners. i 2 c-bus ? logo is a trademark of nxp b.v. 22. contact information for more information, please visit: http://www.nxp.com for sales office addresses, please send an email to: salesaddresses@nxp.com
nxp semiconductors pca6408a low-voltage, 8-bit i 2 c-bus and smbus i/o expander ? nxp b.v. 2012. all rights reserved. for more information, please visit: http://www.nxp.com for sales office addresses, please se nd an email to: salesaddresses@nxp.com date of release: 27 september 2012 document identifier: pca6408a please be aware that important notices concerning this document and the product(s) described herein, have been included in section ?legal information?. 23. contents 1 general description . . . . . . . . . . . . . . . . . . . . . . 1 2 features and benefits . . . . . . . . . . . . . . . . . . . . 2 3 ordering information . . . . . . . . . . . . . . . . . . . . . 3 3.1 ordering options . . . . . . . . . . . . . . . . . . . . . . . . 3 4 block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 3 5 pinning information . . . . . . . . . . . . . . . . . . . . . . 4 5.1 pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 5.2 pin description . . . . . . . . . . . . . . . . . . . . . . . . . 5 6 voltage translation . . . . . . . . . . . . . . . . . . . . . . . 6 7 functional description . . . . . . . . . . . . . . . . . . . 6 7.1 device address . . . . . . . . . . . . . . . . . . . . . . . . . 6 7.2 interface definition . . . . . . . . . . . . . . . . . . . . . . 7 7.3 pointer register and command byte . . . . . . . . . 7 7.4 register descriptions . . . . . . . . . . . . . . . . . . . . 8 7.4.1 input port register (00h) . . . . . . . . . . . . . . . . . . 8 7.4.2 output port register (01h) . . . . . . . . . . . . . . . . . 8 7.4.3 polarity inversion register (02h) . . . . . . . . . . . . 8 7.4.4 configuration register (03h) . . . . . . . . . . . . . . . 8 7.5 i/o port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 7.6 power-on reset . . . . . . . . . . . . . . . . . . . . . . . . 10 7.7 reset input (reset ) . . . . . . . . . . . . . . . . . . . 10 7.8 interrupt output (int ) . . . . . . . . . . . . . . . . . . . 10 8 bus transactions . . . . . . . . . . . . . . . . . . . . . . . 11 8.1 write commands. . . . . . . . . . . . . . . . . . . . . . . 11 8.2 read commands . . . . . . . . . . . . . . . . . . . . . . 12 9 application design-in information . . . . . . . . . 13 9.1 minimizing i dd when i/os control leds . . . . . 13 9.2 power-on reset requirements . . . . . . . . . . . . . 14 10 limiting values. . . . . . . . . . . . . . . . . . . . . . . . . 16 11 recommended operating conditions. . . . . . . 16 12 thermal characteristics . . . . . . . . . . . . . . . . . 17 13 static characteristics. . . . . . . . . . . . . . . . . . . . 17 13.1 typical characteristics . . . . . . . . . . . . . . . . . . 19 14 dynamic characteristics . . . . . . . . . . . . . . . . . 23 15 parameter measurement information . . . . . . 24 16 package outline . . . . . . . . . . . . . . . . . . . . . . . . 28 17 soldering of smd packages . . . . . . . . . . . . . . 31 17.1 introduction to soldering . . . . . . . . . . . . . . . . . 31 17.2 wave and reflow soldering . . . . . . . . . . . . . . . 31 17.3 wave soldering . . . . . . . . . . . . . . . . . . . . . . . . 31 17.4 reflow soldering . . . . . . . . . . . . . . . . . . . . . . . 32 18 soldering: pcb footprints. . . . . . . . . . . . . . . . 34 19 abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . 37 20 revision history . . . . . . . . . . . . . . . . . . . . . . . . 37 21 legal information . . . . . . . . . . . . . . . . . . . . . . 38 21.1 data sheet status . . . . . . . . . . . . . . . . . . . . . . 38 21.2 definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 21.3 disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . 38 21.4 trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . 39 22 contact information . . . . . . . . . . . . . . . . . . . . 39 23 contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

▲Up To Search▲

Price & Availability of PCA6408AHK

	To Download PCA6408AHK Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .